- Thread starter
- #561
Re: Sweetsue's Tiny Closet - Second Grow - Sweet Dark Devil & Bomb Berry Bomb - CFL -
I lifted this from Doc's HB Q&A thread with duggan's permission. Listen up all:
Originally Posted by duggan
Doc , if you don't mind i'de like to share some more electrical info with our members. This would apply to anyone using LED lights with those separate power cords they all seem to come with.After pm'ing with VonD yesterday about his "blown up" socket in his Mars light I decided this info should be shared for safety and reliability issues. The weekest link in all our led lights are the cooling fans....after that it's the connection at the socket on the light. Please keep in mind that all the current these lights draw has to go thru those two little metal prongs or blades on the back(inside the light)of the power socket.When they make them at the factory a real live person has to crimp the Stake-on connectors onto the ends of the power wires before pushing or stabbing them onto those blades or prongs. If that person had a bad day or wasn't carefull enough to make a nice tight firm joint on those , a hot spot develops real fast....after a bit of time ,and people continuously plugging and un-plugging these will loosen it further.....now. guess what ....boom.....your light just blew-up!Ive seen this many times over the years with a lot of different electrical equipment. The main cause for failure is LOOSE joints.When and if you ever have to replace this socket and or power cord remember to use a proper crimping pliers to crimp those Stake-on connectors on the ends of the wire real tight. After you've made this repair it should be a little hard to push them on the blades,that;s good. If they slip on too easy that's trouble waiting to happen. Now ,with these very big and powerfull units coming out these days ....you guessed it ,even more important. If you have to move your lights around for some reason be carefull not to wiggle or mess with that socket end too much.....very important.As soon as this connection point becomes loose and worn a bit you will for sure have problems.
With Vond's light ,he was glad he was home and witnessed it happening, so he could pull the plug real fast.Do not ,I repeat DO NOT attach these wires to the back of the socket with just tape or MCgiver it....use the proper connectors. Taping may work to repair a speaker connection but not a power cord that has to transfer a lot of current.With VonD 's case ,the dealer was nice enough to send him the replacement parts but guess what....they didn't send him the Stake-on connectors he would for sure need to facilitate the repair....without those proper connectors you can't repair it unless you have the ability and means to solder them!Hope everyone sees this as I feel it's very important."Gang"...don't mess with those connection points once your lights are up and running...leave them alone! Cheers....Duggs.
I lifted this from Doc's HB Q&A thread with duggan's permission. Listen up all:
Originally Posted by duggan
Doc , if you don't mind i'de like to share some more electrical info with our members. This would apply to anyone using LED lights with those separate power cords they all seem to come with.After pm'ing with VonD yesterday about his "blown up" socket in his Mars light I decided this info should be shared for safety and reliability issues. The weekest link in all our led lights are the cooling fans....after that it's the connection at the socket on the light. Please keep in mind that all the current these lights draw has to go thru those two little metal prongs or blades on the back(inside the light)of the power socket.When they make them at the factory a real live person has to crimp the Stake-on connectors onto the ends of the power wires before pushing or stabbing them onto those blades or prongs. If that person had a bad day or wasn't carefull enough to make a nice tight firm joint on those , a hot spot develops real fast....after a bit of time ,and people continuously plugging and un-plugging these will loosen it further.....now. guess what ....boom.....your light just blew-up!Ive seen this many times over the years with a lot of different electrical equipment. The main cause for failure is LOOSE joints.When and if you ever have to replace this socket and or power cord remember to use a proper crimping pliers to crimp those Stake-on connectors on the ends of the wire real tight. After you've made this repair it should be a little hard to push them on the blades,that;s good. If they slip on too easy that's trouble waiting to happen. Now ,with these very big and powerfull units coming out these days ....you guessed it ,even more important. If you have to move your lights around for some reason be carefull not to wiggle or mess with that socket end too much.....very important.As soon as this connection point becomes loose and worn a bit you will for sure have problems.
With Vond's light ,he was glad he was home and witnessed it happening, so he could pull the plug real fast.Do not ,I repeat DO NOT attach these wires to the back of the socket with just tape or MCgiver it....use the proper connectors. Taping may work to repair a speaker connection but not a power cord that has to transfer a lot of current.With VonD 's case ,the dealer was nice enough to send him the replacement parts but guess what....they didn't send him the Stake-on connectors he would for sure need to facilitate the repair....without those proper connectors you can't repair it unless you have the ability and means to solder them!Hope everyone sees this as I feel it's very important."Gang"...don't mess with those connection points once your lights are up and running...leave them alone! Cheers....Duggs.