seedingeden
New Member
Perfect
LMAO Cloning For Dummies
- Thread starter Imhigh85
- Start date
907skunk
New Member
Here's some of the clones...hope lil girls make it
- Thread starter
- #323
Imhigh85
Well-Known Member
I think if you just monitor them and make sure the ones that are in water are actually in the water they will all survive and be just fine worst case scenario you might have to get a clear cup and go over top of the plants instead of clear plastic this would allow your cups to become their own Dome kind of like a terrarium
907skunk
New Member
The water is to the top they are about 2 inches under water....yea the humidity is my enemy right now it's low
- Thread starter
- #325
Imhigh85
Well-Known Member
If the low humidity starts to become a problem let me know and we will work on fixing that issue till then I don't think you need to worry about humidity I think they will be just fine
907skunk
New Member
Ok....I don't get to town much to replace my humidifier but I seen a thing about a easy homemade one and it helps
907skunk
New Member
What are symptoms of humidity problems ...I looked it up and guess I don't understand idk
Lilolme
Well-Known Member
Ok.....got it transplanted ....took the 2 cuttings from very bottom....they seem kinda small to me but idk....I did all u said imhigh85....I put this 2 in the cups in the back in the pic...covered cups with clear wrap basically to hold em up...the 2 in the front was lower nodes I cut off I dipped in clone powder and put in soil not sure if those will make or if any of em will....I hope I didn't stress mom too bad cause the pot I had her in was a lil wider on top than the 5gal is so I had to shape the root ball and push a lil....man I hope I didn't mess all this up
Just think about my twig when your feelin unsure of something. It has every reason it should be dead and it all but was. Just strap on a set and get the damn plant into the bucket!
907skunk
New Member
Got em done now time will tell
Lilolme
Well-Known Member
Ok seedingeden here's the pic...I cut where tip of my finger is...one from each side...hard to get pics in there cause is so dense
I did as much work as possible while the branch was still attached. I picked the node I was going to make the final cut at. I carefully removed all the growth at all the nodes on the stalk. I had two to clean up. I used a new razor to remove a very thin layer of material from the stalk. I had a cup of water ready. I make all my cuts no matter what about an inch away from the main growth and leave the extra to dry up. I snipped off the branch and into the water quick. Having done all my prep ahead of time on the stalk I had my scalpel and a block to cut against ready, I made a quick clean cut at an angle through the node I had chosen. About a wink after the cut, into the
Lilolme
Well-Known Member
That's nice to know because that's kind of the setup that I went with other than I'm using Gatorade bottles with very little water and trying to see how long they will survive in there without being exposed to the air
I see nitrogen being introduced into a lot of food products, maybe a small oxygen tank to fill the final package with as close to pure oxygen as you can get short of liquid then quick seal it up. I love my three day rule. I would put together a test package and carry it around eveywhere you go for three days open it up and check it. I want to think my aquatic plants had been in sort of a big single cell bubble wrap. I have a food saver that seals the bags with heat. Put a vial made for cut plants on the end, slip into the bag that can be made pactically any size fill with o2 and seal it.
Lilolme
Well-Known Member
Gonna put this in a box for three days and check it. I also saw despenceries ship with a small led in the package to keep em in veg during shipping.
Lilolme
Well-Known Member
I would call the led company and tell them what you need. A small led with ten hrs or more run time.
I would pay good money to get a good known female cutting in good condition. By good money I mean in the neighborhood of $75 per plant. I would gladly pay that much.
I would pay good money to get a good known female cutting in good condition. By good money I mean in the neighborhood of $75 per plant. I would gladly pay that much.
Lilolme
Well-Known Member
This is the best so far in my search.
Lilolme
Well-Known Member
- Thread starter
- #336
Imhigh85
Well-Known Member
Humidity issues are going to look sort of like plant depression drooping sadness weeping of leaves soft stem
- Thread starter
- #337
Imhigh85
Well-Known Member
My cup clones will have enough roots in 2 days to go into dirt as of today I can see Roots penetrating the stems
Lilolme
Well-Known Member
I would definatly NOT mark the boxes live plants.
Lilolme
Well-Known Member
Mine aint showin much of anything gonna ramp it up. Root goodies.
- Thread starter
- #340
Imhigh85
Well-Known Member
No no no no no markings would be shipped the discreetly so no one is taking a risk
Okay you want to find out if your plans Got Roots we're going to get into real detail now you're going to get inside your clone thing pick your clone up out of the water and look where the roots would be very closely for a little white calcium like spots these calcium like spots turn to roots you can watch these little calcium pieces grow day by day but you have to look very very closely if you need more help with this private message me
Okay you want to find out if your plans Got Roots we're going to get into real detail now you're going to get inside your clone thing pick your clone up out of the water and look where the roots would be very closely for a little white calcium like spots these calcium like spots turn to roots you can watch these little calcium pieces grow day by day but you have to look very very closely if you need more help with this private message me