Advice please

[XiwsX561]

@Pennywise ill give it a shot read can still do anytype of pruning or stress only during the stretch after that dont want to because will waste energy on repairs rather then flowers. @Mikesem420 t6 got here today, should have ordered the nice black ducting they have for it rather then the aluminum one that ill cut from the ipowers 25ft, so until that comes i have it blowing in thru the top. Light hasnt kicked on yet so i have it on auto. So penny ill attempt it with the tallest. Well see what happens. Another way of super cropping i read should be called super cloning, is to take a clipping during the flower period and put it back to 18/6 and it will go back into veg, i assume bc of flowering hormones it grows more rapid.

 

[Pennywise]

No the opposite will occur, the flowering cutting will spend a lot of time revegging instead of growing. It’s called monster cropping.

 

[XiwsX561]

Oh gotcha well here was my attempt hopefully i didnt murder her

 

[XiwsX561]

I guess its pretty even canopy, and i believe this is pre flower?

 

[Pennywise]

Looks good, now watch how fast she recovers.

 

[XiwsX561]

Hopefully i didnt squeeze them too much

 

[Pennywise]

They’ll be fine, they will bounce back in a few hours.

 

[Mikesem420]

Yea I ordered there ducting it really is nice stuff everything they make I was happy with just on the more expensive end. They look really good cannabis is deifinatly a resiliant plant I missed a watering and I came in to a totally wilted plant watered few hours later they where reaching back to the light lol

 

[XiwsX561]

@Pennywise i twist tied them a lil support cause i feel i sqeezed a bit to much and they were bent to far over

 

[Pennywise]

Cool, they will still bounce back quickly.

 

[XiwsX561]

@Mikesem420 i didnt see it until after i ordered it was like 18.99 figured i would just cut a piece off whats coming with ipower. Ya i did that once as well switched my plant to a dwc but i didnt put enough water or maybe it was when i changed my timer i went to work came home thought it was gone put back on timer full time few hrs later it was back. I was reading the manual for the Infinity and says you can only do same size fans dunno if thats a salea tactic or it just wont work. Like i cant put an s4 with my t6 has to be an s6 it says. So t4 and s4 or t6 with s6 and so on.

 

[Mikesem420]

That's why I wish I went with the t6 you can get an s6 and have 2 6inch fans running on the one display but not a t4 and a t6 from what they say havent tried it same plug tho just makes intake/exhaust system super simple set the temp your done no dialing in fans with fan speed controllers... oh well when the time comes I'll ebay my s4 and ipower 6 switch to the t6 or t8 if I'm feeling baller hahaha

 

[XiwsX561]

@Mikesem420 t8 is 199 they even have a t10, what setting do you run yours on? I put fan lvl on like 7 max, then put on auto high temp 82 low 65 high hum 65 low 40, i had on 10 but i dont have duct yet so its just blowing intake in thru the top where my exhaust should be. But that thing moves some air on 10, if i had it to exhaust since no intake just sucking thru the vents on bottom you can see the front flap door suck in.

 

[Mikesem420]

I leave the fan set at max then I go to smart mode and set the temp to 75 the fan auto adjust its speed to the temp it's pretty sweet!

 

[XiwsX561]

@Mikesem420 smart mode and auto same right? U go to on mode to set fan speed then auto and set max temp right

 

[Mikesem420]

Dont have it so high that its blowing the sides out either for now just keep it low to circulate some air when the duct comes switch it

 

[Mikesem420]

No theres actually 2 sperate modes ones called auto mode the other is called smart in smart it will adjust to the temp auto it just turns on or off when it gets up to the selected temp

 

[XiwsX561]

Haha ya it's either sucking them in or blowing them out so i turned it down to 7 but once i get other it will be ok

 

[XiwsX561]

Oh sweet i gotta do that

 

[XiwsX561]

@Mikesem420 not sure but i think they changed the layout of the lcd screen and perhaps the name of that mode bc im not home just looked online at the manual and the pics of lcd are different. Ill check for smart mode later.