Scrogdawg
Well-Known Member
The label says standard dosage is 0.5ml of each part per gallon. Thats where I got it from. I've never had a root issue using it at that strength.
Eeeek!The label says standard dosage is 0.5ml of each part per gallon. Thats where I got it from. I've never had a root issue using it at that strength.
Thank you!
Suntana
Well-Known Member
If Combined no your not, 1ml each, to much lol.
- Thread starter
- #144
JustMeds
Well-Known Member
The label says standard dosage is 0.5ml of each part per gallon. Thats where I got it from. I've never had a root issue using it at that strength.
Ya, that is what I am running. I seen it on label.
- Thread starter
- #145
JustMeds
Well-Known Member
Scrogdawg, I timed a bucket fill. It took 30 minutes to fill 5 gallon bucket to 3" from top (That is the level I needed for the gals). Guessing its 4 gallons then we are at 192 gallons per day. It looked like a 1:1 ratio.
That's a hella veg light! I am outfitting my grow with boards. Same config but will put two boards per rail on two separate rails. More modular. I will use a HLG 240-c2100b and wire the two boards in series. Later I will drop a 3rd board in between to lower the per board current to 700ma.
Your set up looks great. Subbing for the ride.
Your set up looks great. Subbing for the ride.
- Thread starter
- #147
JustMeds
Well-Known Member
ShiggityFlip, welcome aboard lots of room. All are welcome, input is encouraged as I am learning as I go. The ride may be more like sky diving....... Did I grab a shoot or a backpack.. LOL
Scrogdawg
Well-Known Member
Thats a very decent rate, and a good call to get it on your part given the volume you need.
Did the contractor get finished?
- Thread starter
- #149
JustMeds
Well-Known Member
Yes, contractor is done enough. I am thinking these 4 auto's are going to look like a flea on a elephant in this system. LOL I have a cal-mag problem I have to fix today. Took 3-4 days to show with RO water, leaves are all getting pale.
Scrogdawg
Well-Known Member
You'll want about 100-125 ppm of Ca/Mg, increasing to 150-175 ppm later on.
- Thread starter
- #151
JustMeds
Well-Known Member
Made some head way today. Cells are in tent.
Light sitting on cells, Quantum Boards are centered on each cell.
Cells with light off and on.
Light sitting on cells, Quantum Boards are centered on each cell.
Cells with light off and on.
- Thread starter
- #152
JustMeds
Well-Known Member
Kinda looks like that stuff was made to fit that tent..
- Thread starter
- #153
JustMeds
Well-Known Member
They got way more then that today...Hehe May change it out again tomorrow, or may wait till this system is ready.
Skybound
Well-Known Member
yeah it does!
Scrogdawg
Well-Known Member
That looks very very good. But you don't have your air stones in there...
- Thread starter
- #156
JustMeds
Well-Known Member
Got the Res tank set in today.
- Thread starter
- #157
JustMeds
Well-Known Member
Got the chiller installed. Bleach water is running through now.
It's all coming together now. Looks great!
Scrogdawg
Well-Known Member
First class system for sure. Are you going to hang the carbon filter above the lights?
- Thread starter
- #160
JustMeds
Well-Known Member
Nope, right now its set to push into Carbon filter which sits outside tent. I seen no reason to have that in the tent.
Similar threads
