Grandpa Likes To Squeeze Stuff: Solventless Extracts, Rosin, Pressed Here!

BobbyZ said:
So allowing rosin to air out and harden, this results in “wax”?
I don’t think there is a standard for the terminology, I’m trying to make sure I understand.
:lot-o-toke:
Click to expand...

Technically, I think the term wax is used for BHO that is agitated or stirred when evaporating or purging. But, with rosin mine turns pretty waxy if it’s left out. Probably because the RH is pretty low here. It might not be the same where you are. I would imagine that a higher humidity could allow it to ‘cure’ slower. I’m guessing though. I like it waxy. It’s easy to work with. I can plop a piece in the bowl pretty easy.
 
Dutchman1990 said:
Pressing at lower temps will give a sugar or wax like consistency as well. Allowing your rosin to sit out and get touched by the air is allowing it to degrade and lose quality.

Glass air tight containers stored in a cool dry place away from the light is the best.
Click to expand...

I leave it out until it’s gone. It’s still good for weeks.
 
Grandpa Tokin said:
I had to replace a coil in my pen. Warning! Don’t put huge dabs in there. I put way too much apparently...it was dripping all the way down into the battery top. Anyway, put small dabs in there and take small hits.
My Rosin looks good though...yes it does.
Click to expand...

Have you looked at these?

Yocan Evolve Plus Ceramic Coils
 
Grandpa Tokin said:
Technically, I think the term wax is used for BHO that is agitated or stirred when evaporating or purging. But, with rosin mine turns pretty waxy if it’s left out. Probably because the RH is pretty low here. It might not be the same where you are. I would imagine that a higher humidity could allow it to ‘cure’ slower. I’m guessing though. I like it waxy. It’s easy to work with. I can plop a piece in the bowl pretty easy.
Click to expand...
That’s the objective since I’ve got a vape pen on the way...
:high-five:
 
Grandpa Tokin said:
Ordering from Lighter USA. $18 for 5. I wish I would’ve seen these when I ordered. Yay! More money!
Click to expand...
You see what I mean.
3,2,1 and it’s outdated equipment. :straightface: Fudge! It’s not even to my door yet...
 
Grandpa Tokin said:
Ordering from Lighter USA. $18 for 5. I wish I would’ve seen these when I ordered. Yay! More money!
Click to expand...

I kind of figured that them coils would get all gooey, so I orders the ceramic coils also.
 
Grandpa Tokin said:
I had to replace a coil in my pen. Warning! Don’t put huge dabs in there. I put way too much apparently...it was dripping all the way down into the battery top. Anyway, put small dabs in there and take small hits.

My Rosin looks good though...yes it does.

GSC Rosin D2.jpeg

GSC Rosin D2.jpeg


GSC Rosin D2b.jpeg

GSC Rosin D2b.jpeg


Bubblelicious Rosin.jpeg

Bubblelicious Rosin.jpeg

Click to expand...
I warned you pops. about over loading the coils lmao....:passitleft::lot-o-toke::ganjamon::420:
 
I’m ordering these. I like donuts.

Yocan Evolve Plus Coils

The Yocan Evolve Plus Coils are made of Quartz instead of wick to create a pure experience unlike any other. THESE FIT THE YOCAN EVOLVE PLUS AND YOCAN REGEN ONLY Quartz Dual Coil The Quartz Dual Coil is perfect for the the perfect experience. A clean and pure sensation every time. 2 coils...
www.lighterusa.com
 
Grandpa Tokin said:
Ordering from Lighter USA. $18 for 5. I wish I would’ve seen these when I ordered. Yay! More money!
Click to expand...
Grandpa...lil trick, piece of alfoil in a pan, put the coil section in there upside down, heat up over burner, all the,oil runs off, keep moving around until oil is all out with tongs or pliers...HOT!
Make that dead coil like new.

My pen has been tortured, need to buy a new one.
Looking at my 6 tonne shop press and thinking of changing all my plates and control gear onto that.
Will take a few mods but need more squish power I think.

To be honest , my press is cheap and nasty. Opened it up, earth was completely loose, digital gear held in with glue... Is a bitch to clean if you have a run over. The wheel is ok , but the threaded spline makes for uneven contact of plates unless the puck is exactly under the centre thread section, because there is no cage or solid mounting point to keep it,stable.
Just my 2 cents....go dabpress.... Cost me a few hundred and will have to mod it or scrap it....caged plates just a bit more... Grrrr..too hasty.
 
My first question to Alexa. “Alexa?” Blue light comes on, “what’s the best temperature to squeeze GG4?”
She replies, in a very sultry voice, “I don’t know, should I call Grandpa?”

Utterly useless technology...
 
Scottsquatch said:
After she finished talking to you, she notified your local law enforcement agency... LOL Let's hope they dont actually rat people out! My PARANOID self wont use them.
Click to expand...

Now that is a conspiracy theory gone wild.

Is Alexa actually listening, do you really have to say it's name to get it to listen to what you are saying.
If she is, where is that info going? Hell it's marketing, they are not going to turn you in if they have a chance to sell you something. It's similar to the power company, why would they turn you in as long as you pay your bill on time. It would go against the betterment of their shareholders. :)

But I hate that bitch, won't have a damn thing to do with her.
 
Grandpa Tokin said:
My first question to Alexa. “Alexa?” Blue light comes on, “what’s the best temperature to squeeze GG4?”
She replies, in a very sultry voice, “I don’t know, should I call Grandpa?”

Utterly useless technology...
Click to expand...

Saying that, what temp are you squishing that "Wax", does it seem to burn cleaner than the gooey Rosins?
Inquiring minds would like to know!
:passitleft:
 
Back
Top Bottom