Grandpa Likes To Squeeze Stuff: Solventless Extracts, Rosin, Pressed Here!

No pump is needed with the four ton unit. It has a bottle jack, not a hydraulic cylinder.
Which I said so in my post I did recorrect myself as I did say the 4& 10 ton need a pump in which yes u r right the 4 ton does use a bottle jack lol
 
Terp Proof: Not Recommended for Rosin Presses

full

Terp Proof: I'm Excited, and Ready to Cut

full

Terp Proof: Fiberglass & Teflon Close Up
The fiberglass threads are laid vertically and horizintally. They are not woven together.

full

Terp Proof: Ripped After Single Press

I cut 15 sheets for the press. Three out of the first four sheets ripped under the puck after a single press. The intact sheet was subjected to a second press, and ripped apart under the puck. I finished pressing the pre-made pucks using my silicone coated parchment.

The rosin was much more difficult to collect from the Terp Proof, than the parchment. I tried using the Terp Proof to remove the rosin from my collection tool, as I normally do with a silicone mat. It came off of the tool the same way, but then the rosin was difficult to remove from the Terp Proof.

This was an expensive experiment that failed.
 
Ouch

Bummer

Yes, but now no one else needs to try it. I suspect that the rips are due to the uneven surface caused by the fiberglass threads. The puck probably was forced between the threads, and when the puck expanded it forced the threads apart ripping the sheet.
 
Yes, but now no one else needs to try it. I suspect that the rips are due to the uneven surface caused by the fiberglass threads. The puck probably was forced between the threads, and when the puck expanded it forced the threads apart ripping the sheet.
Thanks for sharing bud. First time I’ve saved money on this site...usually I’m buying something. :love:
 
Terp Proof: Not Recommended for Rosin Presses

full

Terp Proof: I'm Excited, and Ready to Cut

full

Terp Proof: Fiberglass & Teflon Close Up
The fiberglass threads are laid vertically and horizintally. They are not woven together.

full

Terp Proof: Ripped After Single Press

I cut 15 sheets for the press. Three out of the first four sheets ripped under the puck after a single press. The intact sheet was subjected to a second press, and ripped apart under the puck. I finished pressing the pre-made pucks using my silicone coated parchment.

The rosin was much more difficult to collect from the Terp Proof, than the parchment. I tried using the Terp Proof to remove the rosin from my collection tool, as I normally do with a silicone mat. It came off of the tool the same way, but then the rosin was difficult to remove from the Terp Proof.

This was an expensive experiment that failed.
Any chance of getting a refund? Just got this from their website.
5F0A11DA-35AE-4168-B1AF-78555871B5A1.jpeg

Doesn’t sound like it meets the standards they’re claiming. Might be worth a phone call?
 
Any chance of getting a refund? Just got this from their website.
5F0A11DA-35AE-4168-B1AF-78555871B5A1.jpeg

Doesn’t sound like it meets the standards they’re claiming. Might be worth a phone call?

I sent them an e-mail detailing what happened, and a link to my post here. We'll see what comes of it.
 
I sent them an e-mail detailing what happened, and a link to my post here. We'll see what comes of it.


Wasn't it like $120

They claim it's the best, they better stand behind it
 
Wasn't it like $120

They claim it's the best, they better stand behind it

Yes, it was $125.96 + $57.34 in taxes and customs for a total of $183.30 CDN. It would make 120 sheets six inches wide, so each sheet would have cost $1.50. It would only have been worth it if I could re-use it five or more times.
 
Yes, it was $125.96 + $57.34 in taxes and customs for a total of $183.30 CDN. It would make 120 sheets six inches wide, so each sheet would have cost $1.50. It would only have been worth it if I could re-use it five or more times.
I'd be on them like flys on shit till they did something
 
I'd be on them like flys on shit till they did something

I start by making a vendor aware of any problem I have with their product, and let them suggest a solution. If their suggestion is not to my liking, or they don't come up with one, I ramp up quickly.
 
Going to pull my press out next week. Have not been doing alot of vaping, COPD got me down. But doing lots of edibles.
Did a journal update today.
Got one more week or so on this ladies.
20200304_141001.jpg 20200304_141007.jpg 20200304_141018.jpg 20200304_141026.jpg 20200304_141033.jpg
 
Going to pull my press out next week. Have not been doing alot of vaping, COPD got me down. But doing lots of edibles.
Did a journal update today.
Got one more week or so on this ladies.
20200304_141001.jpg 20200304_141007.jpg 20200304_141018.jpg 20200304_141026.jpg 20200304_141033.jpg
Something in the air down here GR . I hadn’t smoked in a while . My WW capsules work like burning one and last a lot longer !
 
Hey brotha! Just wanted to cruise through to say hey.

Finally got a decent set of plates & pressed out this pretty booger.
2020-03-07-11-08-22.jpg


Figured you'd enjoy.
:passitleft:

I just had a fat dab of the Doctor. I’m kinda of enjoying the CBD dabs, it gives a nice overall well being feeling. My stuff is still a little moist, so the return wasn’t impressive...
:headbanger:
 
Back
Top Bottom