NeelDJ
Active Member
ok thanks for the review guys.! But now my current condition, since i am planing a small plant, i used a pc box. NOw the tip of plant is about 1 cm below the CFL bulb..How will i control its growth?
First Time Grower - In a PC Box - Challenge Accepted
- Thread starter potturco
- Start date
7Dust
Well-Known Member
that you will learn in time. you can do many ways to control growth. but dont need to do it now. most people if they want small plants they will buy the small short plant seeds. but with what you have 4-5 ft. plant there. but you can top the plant to make more stems and not height. or tie them down. flux them. you just tie the stems down to grow in a direction. if that makes since.
NeelDJ
Active Member
THanks man.. I tied it down today from the main stem.by 24 hours it should come straight back up
NeelDJ
Active Member
Update:
Okay this is my current state:
Had to tie down the the main stem cause it was stretching too much and went about a millimeter away from the CFL.
I used a technique shown in a LST tutorial. And it did work apparently.(cuz the stop sprouting aimed back to the light within 24 hours, as it would, mentioned in the tutorial)the places where i tied is shown below
But now the problem i face is that ...i think it has stopped growing. The growth u see now, is the same size i have been seeing since the past 2 days. The upper most leaves are not even increasing in size after i tied it down.
and moreover the bottom leaves are drying up.
And if i dont water for one whole day, the 3rd and 2nd set of bottom leaves keep drooping down like a zombie bit still green, which didnt used to happen before i tied it down. Well, i know i am again and again referring to the action of 'tying down', but i dont deduce thats the case of my problem. and this leaf in the below image i always faceing down, but not drooping like a zombie.
Then i see root coming out from the place where the main stem and the soil meets. Today i saw one fat root emerging from the soil in that junction. Then i covered that root with soil.
But i still see some white dot like roots appearing.
And is u see the previous images, the leaves on the nodes are increasing really slowly.
Please reply fast....I googled a bit, and i found it my be the case of root bound.,but not sure..
And yea i'm into flowering.
sorry for the low resolution as i was in a hurry
Okay this is my current state:
Had to tie down the the main stem cause it was stretching too much and went about a millimeter away from the CFL.
I used a technique shown in a LST tutorial. And it did work apparently.(cuz the stop sprouting aimed back to the light within 24 hours, as it would, mentioned in the tutorial)the places where i tied is shown below
But now the problem i face is that ...i think it has stopped growing. The growth u see now, is the same size i have been seeing since the past 2 days. The upper most leaves are not even increasing in size after i tied it down.
and moreover the bottom leaves are drying up.
And if i dont water for one whole day, the 3rd and 2nd set of bottom leaves keep drooping down like a zombie bit still green, which didnt used to happen before i tied it down. Well, i know i am again and again referring to the action of 'tying down', but i dont deduce thats the case of my problem. and this leaf in the below image i always faceing down, but not drooping like a zombie.
Then i see root coming out from the place where the main stem and the soil meets. Today i saw one fat root emerging from the soil in that junction. Then i covered that root with soil.
But i still see some white dot like roots appearing.
And is u see the previous images, the leaves on the nodes are increasing really slowly.
Please reply fast....I googled a bit, and i found it my be the case of root bound.,but not sure..
And yea i'm into flowering.
sorry for the low resolution as i was in a hurry
Depot
Well-Known Member
I see what you're trying to do there; You should definitely counter-tie the LOWEST part of the stem to avoid uproot.
If I were you I'd avoid stressing it too much; pull it gradually in the direction you want it to bend.
Check these Low Stress Training guides: Bagz Monthly August 2007 ( LST )
A Brief Guide to LST
Should look somewhat like this
If I were you I'd avoid stressing it too much; pull it gradually in the direction you want it to bend.
Check these Low Stress Training guides: Bagz Monthly August 2007 ( LST )
A Brief Guide to LST
Should look somewhat like this
7Dust
Well-Known Member
if its your first grow i wouldnt do anything till you learn what you can and cant do.
NeelDJ
Active Member
Yup i already did the counter tie in the lowest part. I posted a pic of that too. let me post again for u.I see what you're trying to do there; You should definitely counter-tie the LOWEST part of the stem to avoid uproot.
If I were you I'd avoid stressing it too much; pull it gradually in the direction you want it to bend.
Check these Low Stress Training guides: Bagz Monthly August 2007 ( LST )
A Brief Guide to LST
Should look somewhat like this
Are u saying that i should move the tie lower?
Depot
Well-Known Member
My bad, didn't notice that ahahahYup i already did the counter tie in the lowest part. I posted a pic of that too. let me post again for u.
Are u saying that i should move the tie lower?
Well yeah try moving it lower, but also bend it gradually and you shouldn't have any problem
NeelDJ
Active Member
well, i kinda had my observation incorrect..The top leafing sprout is growing very slowly. And the leaves at the nodes are growing pretty fast
7Dust
Well-Known Member
leaves at top will slow down a little to let the nodes leaves grow to gain light, that's what them leaves are.
that's all a pref there. i might strength one and flux one or top one. depends on my needs. right now i am cloning and topping.
but i got clone fluxing or try to get like 8-9 good stems going.
make some big buds.
i top mine alot. because is easyier. im lazy. lmao.
that's all a pref there. i might strength one and flux one or top one. depends on my needs. right now i am cloning and topping.
but i got clone fluxing or try to get like 8-9 good stems going.
make some big buds.
i top mine alot. because is easyier. im lazy. lmao.
NeelDJ
Active Member
leaves at top will slow down a little to let the nodes leaves grow to gain light, that's what them leaves are.
that's all a pref there. i might strength one and flux one or top one. depends on my needs. right now i am cloning and topping.
but i got clone fluxing or try to get like 8-9 good stems going.
make some big buds.
i top mine alot. because is easyier. im lazy. lmao.
hmm...
retending to understand:
David Bowman
New Member
Hope all is well in your world.
Is this grow still alive?
We would love to be updated with some pictures and info.
How about posting a 420 Strain Review?
If you need any help with posting photos, please read our Photo Gallery Tutorial.
I am moving this to Abandoned Journals until we get updates.
Sending you lots of love and positive energy.
Is this grow still alive?
We would love to be updated with some pictures and info.
How about posting a 420 Strain Review?
If you need any help with posting photos, please read our Photo Gallery Tutorial.
I am moving this to Abandoned Journals until we get updates.
Sending you lots of love and positive energy.
